DOWEI

IEC 62271-205 High-voltage switchgear and controlgear – Part 205: Compact switchgear assemblies for

This part of IEC 62271 applies to compact switchgear assemblies consisting of at least one switching device directly connected to, or sharing components with, one or more other devices such that there is an interaction between the functions of the individual devices. Such assemblies are made up of devices defined in 1.101 and are designed, tested and supplied for use as a single unit. The interaction between devices may be due to proximity, sharing of components or a combination of both. The assemblies may contain components of air insulated switchgear (AIS) only or a combination of AIS and gas insulated switchgear (GIS), so called mixed technology switchgear (MTS) and may be delivered entirely prefabricated or partially assembled.

IEC 62271-207 High-voltage switchgear and controlgear – Part 207: Seismic qualification for gas-insu

This part of IEC 62271 applies to gas-insulated switchgear assemblies for alternating current of rated voltages above 52 kV for indoor and outdoor installations, including their supporting structure.

IEC/TR 62271-306 High-voltage switchgear and controlgear – Part 306: Guide to IEC 62271-100, IEC 622

This part of IEC 62271 is applicable to a.c. circuit-breakers designed for indoor or outdoor installation and for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 1 000 V.

IEC 60071-1 Insulation co-ordination – Part 1: Definitions, principles and rules

This part of IEC 60071 applies to three-phase AC systems having a highest voltage for equipment above 1 kV. It specifies the procedure for the selection of the rated withstand voltages for the phase-to-earth, phase-to-phase and longitudinal insulation of the equipment and the installations of these systems. It also gives the lists of the standard withstand voltages from which the rated withstand voltages are selected.

IEC 61439-1 Low-voltage switchgear and controlgear assemblies – Part 1: General rules

This part of IEC 61439 lays down the general definitions and states the service conditions, construction requirements, technical characteristics and verification requirements for low- voltage switchgear and controlgear assemblies.

IEC 62271-202 High-voltage switchgear and controlgear – Part 202: High-voltage/low-voltage prefabric

This part of IEC 62271 specifies the service conditions, rated characteristics, general structural requirements and test methods of high voltage/low voltage or low voltage/high voltage prefabricated substations, which are cable-connected, to be operated from inside (walk-in type) or outside (non-walk-in type) for alternating current of rated voltages above 1 kV and up to and including 52 kV on the high voltage side, and for one or more transformers for service frequencies up to and including 60 Hz for outdoor installation at locations with public accessibility and where protection of personnel is provided.

IEC 62271-203 High-voltage switchgear and controlgear – Part 203: AC gas-insulated metal-enclosed sw

This part of IEC 62271 specifies requirements for gas-insulated metal-enclosed switchgear in which the insulation is obtained, at least partly, by an insulating gas or gas mixture other than air at atmospheric pressure, for alternating current of rated voltages above 52 kV, for indoor and outdoor installation, and for service frequencies up to and including 60 Hz.

IEEE std 18 Standard for Shunt Power Capacitors

Power capacitors rated 216 V or higher, 2.5 kvar or more, and designed for shunt connection to alternating-current transmission and distribution systems operating at a nominal frequency of 50 Hz or 60 Hz, are considered.

STL Guide to IEC 62271-200 Issue 6.0 20th June 2019 High-voltage switchgear and controlgear

AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

IEEE Std C57.13 Standard Requirements for Instrument Transformers

accuracy, current transformer, IEEE C57.13™, instrument transformer, primary winding, rated secondary voltage, routine tests, secondary winding, type tests, voltage transformer